Edge Profiles, Explained by Fabricators

Countertop Edge Profiles: Eased, Bevel, Ogee, Mitered & More

The edge profile changes how your countertop looks, how much it costs, and how it feels every day. Here is what each profile actually looks like, what it adds to the price, and how it cleans — from the team that cuts them in Hudson, MA.

In-HouseEdge Fabrication
7Profiles Covered
HonestCost Guidance
FreeEstimates

The 7 Edge Profiles Worth Knowing

Every profile below is cut and polished in-house at our Hudson shop. Cost notes are relative to a standard eased edge on the same project.

1. Eased Edge

Look: A nearly square edge with the sharp corner just softened. Clean, modern, and understated — the default on most contemporary kitchens.

Cost: Baseline. Included as the standard edge on most Dream Stoneworks projects.

Cleaning: Easiest to wipe down; no grooves or curves to trap crumbs.

2. Bevel Edge

Look: A straight 45-degree cut along the top edge. Adds a crisp, tailored line that suits transitional kitchens.

Cost: Small upcharge over eased. One extra fabrication pass.

Cleaning: Simple wipe-down; the angled face shows dust a bit more than eased.

3. Bullnose (Full & Half)

Look: Fully rounded (full bullnose) or rounded on top with a flat bottom (half bullnose). Soft and traditional — forgiving on hips and heads in tight kitchens.

Cost: Moderate upcharge. More polishing time than flat profiles.

Cleaning: Smooth curves wipe easily; full bullnose shows fewer chips over time.

4. Ogee Edge

Look: An S-shaped curve that reads formal and classic. A signature look for traditional kitchens and marble vanities.

Cost: Premium. Multiple shaping and polishing passes make it one of the most labor-intensive edges.

Cleaning: The concave curve needs occasional attention with a soft brush to stay crisp.

5. Dupont Edge

Look: A refined stepped profile with a small notch detail near the top. Elegant without the full drama of ogee.

Cost: Premium, similar to ogee. Best on thicker slabs where the detail can show.

Cleaning: Wipe the step ledge during normal countertop cleaning.

6. Mitered Edge

Look: Two pieces joined at 45 degrees to make the countertop look much thicker — often 2 inches or more — while keeping weight down. The modern luxury look for islands.

Cost: Premium. Requires precise miter cuts and a nearly invisible seam, which is skilled labor.

Cleaning: Wipes like a flat edge; the visual thickness is the payoff.

7. Waterfall Edge

Look: The countertop material continues down the side of the island or cabinet to the floor. A dramatic, furniture-like statement.

Cost: Premium, priced per project. Uses significantly more slab and demands exact vein matching at the miter.

Cleaning: Vertical faces wipe down easily; protect the corner from hard knocks.

How to Choose

Start with the kitchen's style: modern kitchens favor eased, bevel, or mitered edges; traditional kitchens favor ogee, dupont, or bullnose. Then weigh cost against impact — a premium edge on the island with a simple edge on the perimeter is a classic way to get the look without paying for it everywhere. Finally, think about daily life: rounded profiles are kinder in busy family kitchens, while crisp mitered corners reward careful use with a striking look.

Edge choice also affects your overall countertop cost, so it is worth deciding before the final estimate. Visit our Northborough showroom to run your hand along full-size samples — an edge you can feel beats one you can only picture.

Edge Profile FAQs

Which countertop edge is cheapest?

The eased edge is the baseline and the most economical choice on nearly every project. It is also the most contemporary look, so budget-friendly and modern go together here.

Which edge profile is best for kitchens with kids?

Rounded profiles like bullnose or a generously eased edge. There are no sharp corners at hip height, and rounded edges are more forgiving if someone bumps into them.

Do mitered edges chip easily?

A well-fabricated mitered edge is strong, but like any edge, the corner is the most exposed point. Eased and bullnose profiles are the most chip-resistant; ogee and dupont details need a bit more care.

Can I mix edge profiles in one kitchen?

Yes. A common approach is a statement edge (mitered or ogee) on the island and a simpler eased edge on the perimeter counters. It saves money while keeping the design impact where guests see it.

How do I choose an edge profile for my project?

Match the edge to the kitchen's style and your tolerance for maintenance: eased or bevel for modern, ogee or dupont for traditional, mitered or waterfall for a luxury island statement. Bring photos to our Northborough showroom and we will show you full-size samples before you decide.

See Edges in Person

Full-size edge samples at our Northborough showroom — 168 Main St. Or start with a free estimate.

The Right Edge, Cut In-House

Every profile on this page is fabricated at our Hudson, MA shop. Tell us the look you want — we will handle the rest.